Newmar is Powering the Network with Isolated converters that provide input/output isolation, allowing use of negative ground electronics on off-highway vehicles which are usually employ positive ground battery systems. The ISP DC-DC Converters provide input/output isolation along with protection against line transients and voltage spikes.

DC Power Stabilizers

Newmar’s Isolated Series converters that provide input/output isolation, allowing use of negative ground electronics on off-highway vehicles which are usually employ positive ground battery systems. The ISP DC-DC Converters provide input/output isolation along with protection against line transients and voltage spikes.

12 & 24 Volt Stabilizing Converters
Feed sensitive electronics with proper voltage regardless of battery condition. These stabilizing converters provide continuous, precisely regulated output over the entire range of a battery's usable voltage. This prevents subjecting loads to fluctuating input voltage which can cause shutdown, diminish performance and possibly damage sensitive circuitry.

Application Benefits Include:
• Operate electronics at optimal input voltage, even from nearly drained batteries
• Boost voltage to compensate for voltage drops in long wire runs from batteries
• Eliminate voltage drops during momentary high current drain from batteries, as during engine start
• Eliminate voltage fluctuation from charge sources
• Eliminate voltage overshoot due to sudden removal of high current load

These converters provide total input/output isolation, virtually eliminating conducted line noise and permitting connection of negative ground gear to positive or floating ground systems, or vice versa. The rugged anodized aluminum case is ideal for mobile applications.

Specifications

Model	Input voltage	Output Voltage	Output Amps Intermittent	Case Size	Weight
Model	Input voltage	Output Voltage	Output Amps Intermittent	Case Size	(Lbs)	(Kg.)

12-12-3I	10-16	13.6	3	C-4	1	.45
12-12-6I	10-16	13.6	6	C-4	1	.45
12-12-12I	10-16*	13.6	12	C-2	6	2.7
12-12-35I	10-16*	13.6	35	C-3	12	5.5
24-24-3I	20-32	27.2	3	C-3	12	5.5
24-24-7I	20-32	27.2	7	C-5	2	.9
48-24-9I	20-56	24.5	9	C-2	8	3.6
48-24-18I	20-56	24.5	18	C-3	12	5.5

*11.5 VDC minimum start-up voltage, then operates @ 10-16 VDC
from 1 amp minimum to full load

Case Size

Ref.	Inches			Centimeters
Ref.	H	W	D	H	W	D
C-1	4.25	5.9	7.7	10.8	15.0	19.6
C-2	4.25	5.9	14.0	10.8	15.0	35.6
C-3	6.0	6.8	16.5	15.2	17.3	41.9
C-4	3.5	3.5	1.75	8.9	8.9	4.5
C-5	7.0	3.5	1.75	17.8	8.9	4.5

Options/Factory Modifications
• Operation as a battery charger (contact factory)
• Parallel/redundant operation (contact factory)
• High vibration mounting kit (see below)
• Non-standard output voltage (contact factory)


Extreme vibration mounting kit The Extreme Vibration Mounting Kit is available to protect NEWMAR power converters from the extreme stresses of shock and vibration when mounted on high–vibration vehicles. The kit (pictured here) replaces the standard vibration kit provided with the unit and fits into the unit's mounting flange to act as a "super shock absorber" for electronics in high-vibe applications. It is available to fit all NEWMAR units from 2 to 70 lbs. Specify KIT–L for units which weigh 2–15 lbs. and Kit–H for units which weigh 16-70 lbs.